Supplies Desired
Two '/*" x Γ eighteen-gauge sterling silver sheet silver Two seven/«" sterling silver bar elements Two 5.3 mm x three.two mm 16-gauge sterling silver oval jump rings Two sterling silver ear wires
TOOLS NEEDED
Ruler
Marker
Jeweler's observed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
Great grit sanding pad Awl
Really hard, flat floor /Îί’ drill bit
Handheld rotary Software, flex shaft, or drill push Liver of sulfur or oxidizing Remedy Wonderful steel wool Sprucing cloth
Two pairs of chain nose pliers
one.Make use of the ruler to measure and mark two
rectangle parts of 18-gauge sterling sheet silver.
two.Utilizing a jeweler's noticed or tin snips, cut the eighteen-gauge sterling sheet silver into two Vi" x Γ rectangles (if you may be earning the bracelet and pendant initiatives, you may want to Slice each of the rectangle silver pieces needed for the opposite projects and texture them all at a person time).
3.Area The 2 W x Γ sterling silver rectangle pieces on to the sticky side of a bit of masking tape. This can help you to carry the silver rectangles set up while you are texturing them, and may even assistance to keep your fingertips at a secure length to stay away from hitting them With all the hammer.
four.Position the bit of masking tape Using the silver rectangles sticky side down onto a concrete block or landscape paver.
five.That has a hammer, Carefully strike the tape-included silver rectangles employing a firm strike, but Do not hit also really hard. You could attain the desired texture much more very easily with a number of comfortable strikes as an alternative to a number of challenging strikes. Raise the tape often and Verify the progress of your texturing, making certain that your entire surface area of the silver rectangles is acquiring a uniform texture. The surface area will appear comparable to sandpaper Should you be using a concrete block. Whenever you reach the desired texture, remove the silver rectangles with the masking tape.
6.the silver rectangles will likely have a slight curve to them, and the edges are going to be misshapen and men's fashion rings sharp Once you texture them. You could leave the silver rectangles curved or, to flatten them, area the silver rectangles on a tough, flat surface area and utilize a rawhide mallet to flatten them. If you don't Possess a rawhide mallet, you could location the silver rectangles on a hard, flat floor, cover the pieces by using a thick piece of scrap leather, and make use of a hammer to Carefully faucet the leather coated silver rectangles to flatten them.
7.You have got to utilize a file to reduce any rough or sharp edges. Use a good grit sanding pad to go about the world in which you have submitted to clean the perimeters and take away any file marks.
eight.Evaluate from one particular close of each and every textured silver rectangle and place a mark in the center of each piece. This is where the holes will likely be drilled to attach the leap ring and bar elements.
9.Placed on the security Eyeglasses. Position the textured silver rectangles onto a hard, flat surface. Spot The purpose on the awl about the mark that you just created '/t" in the end of your rectangle items and use a hammer to firmly strike at the time on the highest from the awl to help make a pilot gap for drilling the holes in to the silver rectangles.
ten.Using mens casual rings a drill little bit, drill holes into Each and every of the silver rectangles by using a handheld rotary tool, flex shaft, or drill push. Make sure to dress in protection glasses.
eleven.Use the file or sanding pad to do away with any burs or rough edges still left from drilling holes into your silver rectangles.
12.Implement liver of sulfur or oxidizing solution on the textured silver rectangles, bar components. and leap rings. It is critical to follow any security suggestions the company indicates when dealing with any substances.
thirteen.Following making use of the oxidizing Option, use great steel wool to remove the darkened locations within the elevated surface area on the silver rectangles, leaving a lot of the textured spots dim. Rub the good steel wool more than the jump rings and bar components to eliminate some although not the entire darkened spots. Rinse with h2o, dry, and rub with sharpening cloth.
14.With two set of chain nose pliers pointing up, maintain the leap men's college ring ring Using the opening at the top. Roll one within your wrists clear of both you and your other wrist toward you, opening the bounce ring only about important. To close the bounce ring, maintain it exactly the same way and roll your wrists in the alternative course (consider mens casual rings Keeping a piece of paper and tearing it). Hardly ever pull the soar ring finishes out as this will likely weaken the metal, and it'll be hard to shut the leap ring.
fifteen.Add men's jewelry the bar part and textured silver rectangle to the soar ring. Shut the leap ring.
sixteen.Carefully open the loop at the bottom of your ear wire, include the opposite end on the bar ingredient. and after that near the ear wire loop.
seventeen.Repeat these steps for the next earring.